Author Topic: Please help ID this tool  (Read 2834 times)

0 Members and 1 Guest are viewing this topic.

Offline knuckleduster

  • Newbie
  • *
  • Posts: 2
Please help ID this tool
« on: March 11, 2012, 08:23:33 PM »
I bought this tool at a flea market because I liked its vintage look.  However, I cannot find any information about it online.  The marking on the tool reads " Guillet Overhauling System Precision Alignment."  There is no patent number or other identifying info on the tool.  I'm assuming that it was used for auto work or machining.  I would like to find out what it was specifically used for and to date it.  Any assistance/info would be appreciated!

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: Please help ID this tool
« Reply #1 on: March 11, 2012, 08:39:58 PM »

This is a long shot, but , there was a fellow at Penn state, Professor of mechanical engineering, wrote a book 'Kinematics of machines', around 1940-1950's, named George Leroy Guillet.....

Some kind of calibration/alignment tool....(?)
Just a weathered light rust/WD40 mix patina.

Offline Papaw

  • Owner/Administrator
  • Administrator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: Please help ID this tool
« Reply #2 on: March 11, 2012, 08:49:17 PM »
Connected to DIXIE SPINDLE & FLYER COMPANY, INC. , but I didn't find much other than trademark info.
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline Mac53

  • Hero Member
  • *****
  • Posts: 203
Re: Please help ID this tool
« Reply #3 on: March 11, 2012, 09:48:08 PM »
Can you get a shot of the bottom?
-Marcus-

Offline amertrac

  • Contributor
  • Hero Member
  • *****
  • Posts: 1880
  • ny mountain man
Re: Please help ID this tool
« Reply #4 on: March 12, 2012, 07:00:43 AM »
It is a double hand to eye co-ordination tester  or a nut cracker  bob w.
TO SOON ULD UND TO LATE SCHMART

Offline keykeeper

  • Hero Member
  • *****
  • Posts: 1053
Re: Please help ID this tool
« Reply #5 on: March 12, 2012, 07:46:40 AM »
Using this http://www.trademarkia.com/guillet-overhauling-system-71572027.html

I found this http://www.google.com/patents?id=S2BaAAAAEBAJ&pg=PA2&dq=guillet+alignment+textile&hl=en&sa=X&ei=W-5dT4i3DoLF0AGyrcDSDw&ved=0CDQQ6AEwAA#v=onepage&q=guillet%20alignment%20textile&f=false

I believe this is part of a later system from this inventor, used in the textile industry to adjust roll stand bearings.

Just a WAG, based on what I found.

(PS: Are you the same knuckleduster from over in Maryland? I think I sold you a pair a while back!!)
-Aaron C.

My vintage tool Want list:
Wards Master Quality 1/2" drive sockets (Need size 5/8), long extension, & speeder handle.
-Vlchek WB* series double box wrenches.
-Hinsdale double-box end round shank wrenches.

Offline knuckleduster

  • Newbie
  • *
  • Posts: 2
Re: Please help ID this tool
« Reply #6 on: March 12, 2012, 04:35:51 PM »
Thanks to all for the speedy replies!  Papaw and keykeeper shed some light on its origins.  Keykeeper, must have been a different knuckleduster you dealt with regarding the sale.  Thanks again for digging up the info!   

Offline Papaw

  • Owner/Administrator
  • Administrator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: Please help ID this tool
« Reply #7 on: March 12, 2012, 07:26:34 PM »
Keykeeper, that is Knucklebuster on Garage Gazette you're thinking of, I bet.
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline keykeeper

  • Hero Member
  • *****
  • Posts: 1053
Re: Please help ID this tool
« Reply #8 on: March 12, 2012, 08:58:56 PM »
Naw, I sold a fella a set of antique Civil War era iron knucks a while back. Knuckleduster was his handle on a chat board I found him on.

Just thought it may be the same fella.
-Aaron C.

My vintage tool Want list:
Wards Master Quality 1/2" drive sockets (Need size 5/8), long extension, & speeder handle.
-Vlchek WB* series double box wrenches.
-Hinsdale double-box end round shank wrenches.