« previous next »
Pages: [1]   Go Down

Author Topic: Metalworking Vise ID?  (Read 2240 times)

0 Members and 1 Guest are viewing this topic.

Offline Bill Houghton

  • Hero Member
  • *****
  • Posts: 2860
Metalworking Vise ID?
« on: August 12, 2018, 09:38:15 PM »
Picked up the odd vise below yesterday; jaws are about 5". Anyone recognize the logo (dykem's been added to the logo area to highlight it)?

The rear jaw moves, on dovetailed ways with an adjusting gib, the same sort of design some woodworking jointers use.
« Last Edit: August 12, 2018, 09:39:52 PM by Bill Houghton »
Logged

Offline mikeswrenches

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2002
Re: Metalworking Vise ID?
« Reply #1 on: August 13, 2018, 08:30:44 AM »
Bill, most of those, maybe all, are made in Poland. Generally considered to be an excellent vise. I had one several years ago and I remember it primarily because it was extremely heavy and it had adjustable gibs on the dovetail slide.

Mike
Logged
Check out my ETSY store at: OldeTymeTools

Offline Bill Houghton

  • Hero Member
  • *****
  • Posts: 2860
Re: Metalworking Vise ID?
« Reply #2 on: August 13, 2018, 09:00:04 AM »
Thanks.  Over on Old Woodworking Machines, it was identified as Polish, and I found a bunch of them on eBay.

I'm curious: what did you like/not like about it, besides the heft?
Logged

Offline Yadda

  • Hero Member
  • *****
  • Posts: 1991
Re: Metalworking Vise ID?
« Reply #3 on: August 13, 2018, 09:09:40 AM »
That look like one beast of a vise. How much does it weigh?
Logged
You might say I have a tool collecting problem....

Offline kwoswalt99

  • Hero Member
  • *****
  • Posts: 223
Re: Metalworking Vise ID?
« Reply #4 on: August 13, 2018, 02:04:57 PM »
It’s FPU Bison.
Logged

Offline wrenchguy

  • Hero Member
  • *****
  • Posts: 480
  • I like odd old stuff, especially mechanical.
    • Wrenchguys videos
Re: Metalworking Vise ID?
« Reply #5 on: August 14, 2018, 07:19:24 AM »
it opens weirdly, the rear jaw travels away from u and can't chuck anything up that drops below edge of bench.  they r hell4stout.
Logged

Offline mikeswrenches

  • In Memoriam
  • Hero Member
  • *****
  • Posts: 2002
Re: Metalworking Vise ID?
« Reply #6 on: August 14, 2018, 10:00:33 AM »
Quote from: Bill Houghton on August 13, 2018, 09:00:04 AM
Thanks.  Over on Old Woodworking Machines, it was identified as Polish, and I found a bunch of them on eBay.

I'm curious: what did you like/not like about it, besides the heft?

As wrenchguy said, the movable rear jaw is too unwieldy. Also the shallow jaw depth is another issue. I use an old Prentiss coach makers vise myself because I like the smooth jaws and the deep throat. Plus the rear jaw stays put and doesn’t move.

Mike
Logged
Check out my ETSY store at: OldeTymeTools

Offline Bill Houghton

  • Hero Member
  • *****
  • Posts: 2860
Re: Metalworking Vise ID?
« Reply #7 on: August 14, 2018, 11:05:30 AM »
But they sell for fairly big money on That Auction Site, particularly so considering that freight is $50 and up; so there must be folks who find them the right vise (as opposed to the right vice, which is, of course, tool gathering).
Logged

Offline wrenchguy

  • Hero Member
  • *****
  • Posts: 480
  • I like odd old stuff, especially mechanical.
    • Wrenchguys videos
Re: Metalworking Vise ID?
« Reply #8 on: August 17, 2018, 07:01:44 AM »
Quote from: Bill Houghton on August 14, 2018, 11:05:30 AM
But they sell for fairly big money on That Auction Site, particularly so considering that freight is $50 and up; so there must be folks who find them the right vise (as opposed to the right vice, which is, of course, tool gathering).

Precisely made,  definitely has a place on the bench when u know its advantages and limitations. i got several 6"ers, as well as parts 1's.
Logged
Pages: [1]   Go Up
« previous next »