« previous next »
Pages: [1]   Go Down

Author Topic: Reed #700  (Read 1570 times)

0 Members and 1 Guest are viewing this topic.

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Reed #700
« on: May 19, 2014, 06:57:48 AM »
Nice old pipe vise should clean up nicely.




and this V&C

Logged
RooK E

Offline bonneyman

  • Hero Member
  • *****
  • Posts: 1743
Re: Reed #700
« Reply #1 on: May 19, 2014, 10:18:39 AM »
Nice vises! Is the V&C missing the bottom set of teeth, or is it supposed to be that way?
Logged
Ratchet Guru

Offline Bill Houghton

  • Hero Member
  • *****
  • Posts: 2854
Re: Reed #700
« Reply #2 on: May 19, 2014, 03:57:22 PM »
How does the V&C work?  To what does it fasten?
Logged

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: Reed #700
« Reply #3 on: May 19, 2014, 04:02:10 PM »
Not sure if it has another set of jaws or not. The hump at the top has an opening for a pipe or whatever they used. I'll get a pic of the opening here in a minute.
Logged
RooK E

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: Reed #700
« Reply #4 on: May 19, 2014, 04:12:30 PM »
The V&C is missing it's bottom jaw :(

The patent is 709944 ....

PS: Is actually V&G (John B. Vogelbach, Thomas Gray)
« Last Edit: May 19, 2014, 04:20:06 PM by rusty »
Logged
Just a weathered light rust/WD40 mix patina.

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: Reed #700
« Reply #5 on: May 19, 2014, 04:30:34 PM »



What is this called? Has pat'd Nov. 16, 1875 on it. Side view is what is holding up the vise.



Logged
RooK E

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: Reed #700
« Reply #6 on: May 19, 2014, 04:32:28 PM »
Forgot to add that the opening is 7/8" so it was probably 3/4" galvanized pipe.
Logged
RooK E

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: Reed #700
« Reply #7 on: May 19, 2014, 04:44:03 PM »
Quote from: rusty on May 19, 2014, 04:12:30 PM
The V&C is missing it's bottom jaw :(

The patent is 709944 ....

PS: Is actually V&G (John B. Vogelbach, Thomas Gray)
Guess that means why I came up empty looking around for it at vises&clamps.
Datamp says Patent not found, where did you search?
Logged
RooK E

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: Reed #700
« Reply #8 on: May 19, 2014, 05:10:07 PM »
Logged
Just a weathered light rust/WD40 mix patina.

Offline HeelSpur

  • Hero Member
  • *****
  • Posts: 2033
  • Contributor
Re: Reed #700
« Reply #9 on: May 19, 2014, 05:19:09 PM »
Logged
RooK E
Pages: [1]   Go Up
« previous next »