« previous next »
Pages: [1]   Go Down

Author Topic: Curved Wheaton wrench goes to what piece of equipment?  (Read 3665 times)

0 Members and 1 Guest are viewing this topic.

Offline Wrenchmensch

  • Contributor
  • Hero Member
  • ***
  • Posts: 1114
  • Wrenches tell of man's freedom to think
Curved Wheaton wrench goes to what piece of equipment?
« on: December 15, 2012, 02:51:17 PM »
We made it a point to stop off at a new Farmers Market today.  I found this uncommon Wheaton wrench with a curved handle, bent up at the end. It's 9 inches long, and is embossed 8 C W followed by a rhombus on the reverse side of the handle. I have found several of the straight Wheaton wrenches over the years, but this is the first one of these I have seen.  What's it for, does anybody know?

P.S.  I've emailed 100-year old EMCO Wheaton and asked them what this wrench was used for.  I'll share here whatever answer, if any, they give me.

B. 
« Last Edit: December 15, 2012, 10:05:43 PM by Wrenchmensch »
Logged

Offline john k

  • Contributor
  • Hero Member
  • ***
  • Posts: 2657
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #1 on: December 15, 2012, 06:22:03 PM »
The more I look at it, reminds me of a tool to run the shakers back and forth on a coal furnace.  One had to do that daily to push the clinkers down out of the firebox.    I don't find much on Wheaton Industries except for a glass company.
Logged
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society

Offline Billman49

  • Hero Member
  • *****
  • Posts: 790
  • Collector of edged tools, especially billhooks...
    • A Load of Old Billhooks
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #2 on: December 16, 2012, 12:30:29 PM »
Looks a bit like an oil valve key as used on fuel tankers (trucks)
Logged

Offline Wrenchmensch

  • Contributor
  • Hero Member
  • ***
  • Posts: 1114
  • Wrenches tell of man's freedom to think
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #3 on: December 19, 2012, 10:22:39 AM »
Below is the response received today from EMCO Wheaton.  Struck out there, but will keep on trying elsewhere.

Diane.Wallace@emcowheaton.com
   
11:00 AM (18 minutes ago)
      
to me
Hi Bob,

I showed your photos to everyone in the office, but they are not sure what
these were used for.   Wish we could help you, but nobody can identify
them.

Diane

Diane Wallace
Sales Coordinator II - Houston
Tel:   281.856.3906
Fax:  281.856.1325
www.emcowheaton.com
Logged

Offline Wrenchmensch

  • Contributor
  • Hero Member
  • ***
  • Posts: 1114
  • Wrenches tell of man's freedom to think
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #4 on: December 25, 2012, 04:27:21 PM »
So, I'll put this "orphan" into one of the Rubbermaid tubs for the next trip.
Logged

Offline rusty

  • Hero Member
  • *****
  • Posts: 4345
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #5 on: December 25, 2012, 06:08:10 PM »
>Looks a bit like an oil valve key as used on fuel tankers (trucks

A. W. Wheaton Brass Works of Newark New Jersey made valves and tank filling apparatus for the petroleum industry....


Edit: Duh - same company Wheaton Brass + Emco(Empire Mfg Co ) = emcowheaton ;P
« Last Edit: December 25, 2012, 06:47:28 PM by rusty »
Logged
Just a weathered light rust/WD40 mix patina.

Offline Wrenchmensch

  • Contributor
  • Hero Member
  • ***
  • Posts: 1114
  • Wrenches tell of man's freedom to think
Re: Curved Wheaton wrench goes to what piece of equipment?
« Reply #6 on: December 26, 2012, 09:06:31 AM »
Thanks Rusty!  Makes sense.
Logged
Pages: [1]   Go Up
« previous next »