Author Topic: Really weird hammer  (Read 3028 times)

0 Members and 1 Guest are viewing this topic.


Offline amertrac

  • Contributor
  • Hero Member
  • *****
  • Posts: 1880
  • ny mountain man
Re: Really weird hammer
« Reply #1 on: February 14, 2012, 06:04:29 PM »
very interesting  bob w.
TO SOON ULD UND TO LATE SCHMART

Offline anglesmith

  • Hero Member
  • *****
  • Posts: 409
  • Mid Northcoast NSW Australia
Re: Really weird hammer
« Reply #2 on: February 14, 2012, 06:23:22 PM »
Surley its some sort of" testing" or maybe a flint napping hammer? But I can't imagine someone sitting in the middle of the road breaking stone into 3/4" gravel size pieces with 1,1/2lb thin handled hammer! Does nappan = napping?
Graeme

Offline johnsironsanctuary

  • Contributor
  • Hero Member
  • ***
  • Posts: 1908
  • Super Contributor and Geezer in training
Re: Really weird hammer
« Reply #3 on: February 14, 2012, 07:44:06 PM »
I think that it is an anesthetic for cows at the slaughterhouse.
Top monkey of the monkey wrench clan

Offline Branson

  • Hero Member
  • *****
  • Posts: 3643
Re: Really weird hammer
« Reply #4 on: February 15, 2012, 08:46:49 AM »
I'm pretty sure that this is a stone carving mallet.

Offline johnsironsanctuary

  • Contributor
  • Hero Member
  • ***
  • Posts: 1908
  • Super Contributor and Geezer in training
Re: Really weird hammer
« Reply #5 on: February 15, 2012, 12:10:46 PM »
I don't think so Branson. The close up shows a rough cast iron texture. Unless it is unused, the head would have marks from thumping on hardened chisels.
Top monkey of the monkey wrench clan

Offline keykeeper

  • Hero Member
  • *****
  • Posts: 1053
Re: Really weird hammer
« Reply #6 on: February 15, 2012, 01:46:41 PM »
I've seen them listed in old catalogs as macadamizing hammers as well.

-Aaron C.

My vintage tool Want list:
Wards Master Quality 1/2" drive sockets (Need size 5/8), long extension, & speeder handle.
-Vlchek WB* series double box wrenches.
-Hinsdale double-box end round shank wrenches.

Offline lazyassforge

  • Sr. Member
  • ****
  • Posts: 176
Re: Really weird hammer
« Reply #7 on: February 15, 2012, 02:06:55 PM »
I didn't think the answer about the hammer being used to make gravel was right! So I searched and found this site with a print of people using simular hammers to make gravel! I was wrong!

http://www.semp.us/publications/biot_reader.php?BiotID=484

Interesting, How long did it take them to pave a mile?

Hope this helps, Bill D.

Offline Papaw

  • Owner/Administrator
  • Administrator
  • Hero Member
  • *****
  • Posts: 11221
  • Alvin, Texas
    • Papawswrench
Re: Really weird hammer
« Reply #8 on: February 15, 2012, 04:25:13 PM »
I knew about macadam roads from studies in history, even to the resulting tarmac roads later, but never knew the full story until now.
Thanks for that link!
Member of PHARTS - Perfect Handle Admiration, Restoration and Torturing Society
 
 Flickr page- https://www.flickr.com/photos/nhankamer/

Offline Branson

  • Hero Member
  • *****
  • Posts: 3643
Re: Really weird hammer
« Reply #9 on: February 16, 2012, 08:09:57 AM »
I don't think so Branson. The close up shows a rough cast iron texture. Unless it is unused, the head would have marks from thumping on hardened chisels.

Just to point out, if it was used to break up stone, as apparently it was  (I should have looked at the rest of the pictures) it would have had marks from thumping on stone -- quartz is a good deal harder (70 Rockwell) than most chisels.

Offline johnsironsanctuary

  • Contributor
  • Hero Member
  • ***
  • Posts: 1908
  • Super Contributor and Geezer in training
Re: Really weird hammer
« Reply #10 on: February 16, 2012, 08:35:47 AM »
But not from limestone or other soft aggregates.
Top monkey of the monkey wrench clan