Tool Talk
Buying, Selling, and Trading => Buying, Selling, and Trading => Topic started by: OilyRascal on September 07, 2013, 03:09:08 PM
-
An important person in my life has spoken up to say he has a need for combination wrenches greater than 1-1/4", stepping up to about 2" (being the desire). This is a person that rarely expresses a need or want and that has helped me many times in the past, so I would like to try and help.
I'm in the market for good quality USA made combination wrenches that cover anything in the 1-1/4" - 2" range. They do not need to be matching sets or have matching branding. They can be rusty and ugly. They just need to work. I have until late November to fill the order. Any help from the forum in "finds" would be greatly appreciated. I have both cash and trade stock. Probably a lot more of the latter thanks to my tool addiction.
-
I have a Williams 1039C Superrench 1 7/16 x 1 3/8 and a Plomb pebble 3055 1 5/16 x 1 1/4 to help get you started. A trade would be as good or better than cash for me, too. I'd be more interested in metalworking or machinist tools than mechanic's tools, but would be open to about anything. Sounds like this is pretty important to you, so don't worry too much about the trade. In fact, if you pm me your shipping information, I'll get the wrenches out to you and we can work out the trade later.
-
I think I have three American made 1 1/4, and one two inch wrenches I can part with, I will get back to you tomorrow when I go out to the shop. However I could be wrong but will look to see what I have
-
Thank you both! PM inbound.
-
Oily, I have 1 1/8 and 1 1/4 combos if needed.
Brian
-
Mr. Brian - Thank you so much for the offer. Ron has offered to send me the 1-1/4", and I was specifically told the recipient already has an 1-1/8". I do very much appreciate the consideration and offer.
At this point I lack those 1-1/2" and above, or more specifically the following:
1-1/2"
1-9/16"
1-5/8"
1-11/16"
1-3/4"
1-13/16"
1-7/8"
2"
-
Sent you a private message.
-
I have covered some ground on this project in the last couple weeks. An overall photo and two close-ups below:
(http://i1154.photobucket.com/albums/p534/alphinde/Tools%20Talk/CIMG6403_zps572b8eb7.jpg) (http://s1154.photobucket.com/user/alphinde/media/Tools%20Talk/CIMG6403_zps572b8eb7.jpg.html)
(http://i1154.photobucket.com/albums/p534/alphinde/Tools%20Talk/CIMG6404_zps76926697.jpg) (http://s1154.photobucket.com/user/alphinde/media/Tools%20Talk/CIMG6404_zps76926697.jpg.html)
(http://i1154.photobucket.com/albums/p534/alphinde/Tools%20Talk/CIMG6405_zps22994d19.jpg) (http://s1154.photobucket.com/user/alphinde/media/Tools%20Talk/CIMG6405_zps22994d19.jpg.html)
Details (from right to left in the overall)
Proto 2" combo
Armstrong Armaloy 1-5/8" combo
Proto Challenger 1-5/8" combo
Armstrong Armaloy 1-1/2" combo
Williams 1-5/8" x - 1-7/16" DBE
Proto 1-1/2" x 1-7/16" DBE
VLCHEK 1-1/2" x 1-7/16" DBE Offset
Proto Pro 1-7/16" combo
Williams 1-7/16" x 1-3/8" DOE
Proto Challenger 1-1/4" combo
S-K 1-1/8" combo
Plumb (pebble no less) 1-1/4" x 1-5/16" DOE
Tru-Test (USA) 1-1/8" combo
Bonaloy 1-1/8" combo
Williams 1-1/4" x 1-1/16" DOE
Proto 1-1/16" combo
A special thank you to Ron Walters and Bill Houghton for helping me in my search.
At this point I lack the following:
1-9/16"
1-11/16"
1-3/4"
1-13/16"
1-7/8"