Tool Talk

What's-It Forum => What's-It Forum => Topic started by: dimwittedmoose51 on May 28, 2012, 05:07:53 AM

Title: 5" Knurled Handle....but for what??
Post by: dimwittedmoose51 on May 28, 2012, 05:07:53 AM

Threads appear to have a slight taper to them, so is this a handle for a mini hammer/kit tool or some weird item some one made in a metal shop project.  No logos or numbers anywhere. Old enough to likely not be Asian, so I'm stumped again this week.  TIA gang!!


DM&FS

Title: Re: 5" Knurled Handle....but for what??
Post by: Papaw on May 28, 2012, 06:01:29 AM

I never took metal shop, so I must ask- can you make such nice knurling in a one-off project?

Title: Re: 5" Knurled Handle....but for what??
Post by: RedVise on May 28, 2012, 08:53:41 AM

Metal shop was in 73, so it's been a while... but you are cutting that down in a lathe and you would use a knurling tool to apply.
Nice video here

http://www.technologystudent.com/equip1/knurl1.htm


Brian L.

Title: Re: 5" Knurled Handle....but for what??
Post by: rusty on May 28, 2012, 09:07:04 AM

Could also have been a handle for a clamping jig. I've seen die makers go somewhat over indulgent at times ;P

Yea, the knurl is the easy part, oddly, the pipe thread is the hard part....

It would make a great handle for a small tapping hammer :)

Title: Re: 5" Knurled Handle....but for what??
Post by: superzstuff on May 28, 2012, 12:18:43 PM

I was a diemaker for 38 years and I used a bar like this to turn dies on their side to seperate top and bottom. We had over 1000 dies and those that were too big to handle by hand had 1/2" to 5/8" threaded holes on all sides to handle them. Sometimes we used a chain fall, sometimes a handling bar. Or it could just be a threaded handle.

Title: Re: 5" Knurled Handle....but for what??
Post by: scottg on May 30, 2012, 01:09:23 PM

Hey wait a minute, a diemaker???
  Ohhhhh hoo hoo going to pick a brain over this!!!

  So, knurling? I only have a single knurl holder. Never did have a dual or certainly not a turret.
I got some loose knurls one time, but haven't mounted them.   
Do you have any advise for me? I have a small lathe, 6X18 Atlas.

 Also, I always started with the lathe off, apply a bit of pressure, turn it on and increase the pressure. This is wrong?

 Here are a couple knobs I made. Look em over and see if anything occurs to you that would make it easier for me?   
 I generally use a lathe the same way I'd use a file. By guess and by god, as they say. heh
  yours Scott
 

Title: Re: 5" Knurled Handle....but for what??
Post by: johnsironsanctuary on May 30, 2012, 01:45:16 PM

Sure looks like the handle from a high school machine shop project hammer.

Title: Re: 5" Knurled Handle....but for what??
Post by: dimwittedmoose51 on May 30, 2012, 05:34:01 PM

I would agree with that!!

DM&FS

Title: Re: 5" Knurled Handle....but for what??
Post by: superzstuff on May 30, 2012, 06:10:07 PM

A good knurl takes lost of pressure and a sturdy lathe. Knurl rollers in good condition will displace metal much better. There are scissor type knurl tools that are brought together with a screw that don't put pressure on your lathe. Also, keep knurl teeth clean, but don't get wire brush caught in work. (Yes, I did a few times.) I guess you know brass knurls better than tool steel, but you can do either with good results.

Title: Re: 5" Knurled Handle....but for what??
Post by: stanley62 on June 04, 2012, 04:38:49 PM

The piece reminds me of a piece of the holder for my Lansky knife sharpener.  The threaded end goes into a base that can be clamped to a bench.  The top bit, above the knurl, fits into a hole on a clamp to hold the workpiece (knife) in place while you work on it.  This allows you to quickly flip workpiece over without reclamping.
  I am thinking this is a user made piece for something similiar.

  Jim